Every fall I talk to cow-calf guys who are done rolling out bales and watching a third of the hay get trampled. They’ve got about 100 cows, a decent tractor, and one question: what size feed mixer do I actually need? It’s a fair question. Buy too small and you’re mixing all morning. Buy too big and you’ve paid for steel you’ll never fill.
Here’s how I’d work it out for a 100 cow beef herd on a hay and silage ration. The numbers below are an example. Your ration and your cows will change them, so run your own.
Start with the daily ration volume
Begin with how much feed goes out per day, not with mixer size.
- A mature beef cow commonly eats somewhere around 2% of her body weight in dry matter per day. Your nutritionist can give you the right figure for your cows and their stage.
- Convert that to as-fed weight using the moisture in your ration. Silage carries a lot of water, so as-fed weight goes up fast.
- Multiply by head count. For 100 cows, that’s your daily as-fed total.
Then turn weight into volume. A bulky hay-heavy ration is light per cubic metre, while a silage-heavy ration is denser. That density is what decides tub size, and it’s the step most people skip.
How many loads per day
Once you know daily volume, decide how many loads you want to mix.
- One load a day is simple, but it needs the biggest tub.
- Two loads a day lets you go smaller and gives fresher feed, but it doubles mixing time and fuel.
For most 100 cow herds feeding once a day, people look at fitting the whole day’s ration in one load with some room to spare. If you’d rather feed twice, half the volume per load opens up smaller mixers.
Choosing tub size with room for bulky hay
Hay and straw take up a lot of space before they’re processed. A tub that holds the finished ration by volume may still be too tight while whole bales are breaking down.
- Don’t plan to fill to the brim. Leave working room so feed can turn over and mix evenly.
- If round bales are a big part of the ration, size up a little or plan to process bales first and let them break down before adding the rest.
- Think about the next few years. If the herd is going to grow, buy for that herd.
For herds this size, a small or mid-size vertical often makes sense. Our mini mixers are built for small to mid-scale operations, and the VT twin auger feed mixers cover 6 to 21 cubic metres if you need more room.
Tractor horsepower and loader pairing
The mixer is only half the setup.
- Check the horsepower and PTO requirement for the mixer you’re looking at. Bigger tubs and tough bales need more power, especially at start-up.
- Make sure your tractor can handle the loaded weight safely on your yard, including icy winter ground.
- Look at your loader height. You need to clear the tub wall with a bale or bucket comfortably.
- Bucket size matters too. A small bucket on a big mixer means a lot of trips.
A simple winter feeding setup
Keep it simple: one mixer, one loader tractor, a clean pad near the bales and silage, and a feed line the mixer can drive along. Put the scale indicator where the loader operator can see it. That alone saves a lot of wasted feed.
Quick questions
Will a mixer pay for itself with 100 cows? It depends on how much hay you waste now and your labour and fuel. Run the numbers on your own operation before you buy.
Can I mix just hay? Yes. Many beef herds mix hay with a bit of silage, straw or byproducts to stretch forage.
Single or twin auger? Both can work. Twin augers handle larger tubs and bulky feed well. Ask about your ration.
Do I need a scale? Yes. It’s how you know every cow is getting what you planned.
Bottom line?
Size the mixer from the ration, not the herd count alone. Work out daily volume, pick loads per day, leave room for bulky hay, and match the tractor. If you want help running your numbers, contact us or reach out to your nearest dealer.
Learn more about LEO Agriculture and our full line of feed mixers and manure spreaders.
