It’s 5 a.m., it’s well below freezing, and the feed mixer won’t turn over. Or it turns over, groans, and throws a shear bolt on the first frozen chunk of silage. Every winter I hear the same calls. And almost every one of them could have been headed off with an hour of checks in October or November.
Cold weather doesn’t change what a vertical feed mixer does. It changes how hard everything has to work to do it. Oil gets thick, steel gets brittle, batteries lose punch, and feed comes in harder and lumpier than it did in September. Here’s what I’d look at before the first hard freeze.
Gearbox oil: grade and level first
The planetary gearbox is the heart of a vertical mixer. In the cold, the wrong oil gets thick and slow, and the first few minutes of every morning are hard on gears and bearings.
- Check your operator’s manual for the recommended oil grade across your temperature range. Some operations run a different grade in winter. Don’t guess.
- Check the level with the mixer sitting level. Low oil plus cold oil is a bad combination.
- Look at the drained oil if it’s due for a change. Milky oil means water got in. Metal flakes mean it’s time for a closer look.
- Don’t forget the PTO driveline. Grease the crosses and the slip clutch or shear bolt area so it can do its job.
Frozen silage, knives and auger load
Frozen feed is the big one. A chunk of frozen silage or a frozen bale core puts a shock load straight through the auger, the knives and the gearbox.
- Break up frozen faces before they go in the tub. Your loader can do this. Your mixer shouldn’t have to.
- Check knives now. Dull knives make the auger push harder through tough material, and that load gets worse when feed is frozen. If you’ve been putting off a knife change, winter is not the time to keep putting it off.
- Start the auger before loading, at low speed, and load the bulky or frozen stuff gradually.
- Keep the right shear bolts on hand. A harder bolt to “stop them breaking” just moves the break somewhere more expensive.
Scale indicator, wiring and battery care
A scale that drifts or dies in January means guessing every load. Guessing in winter means wasted feed or short-fed cattle.
- Clean and dry the connectors on load cells and the indicator. Moisture gets in, freezes, and connections go bad.
- Check cables for chafing where they run near moving parts or along the frame.
- If the indicator runs off the tractor, check that the tractor battery and alternator are healthy. Weak power can cause flickering readings.
- Re-zero the scale on a cold morning once the mixer is empty and clean, and check it against a known weight if you can.
Clean out before it freezes in
Feed left in the tub overnight in freezing weather turns into a block. Then you’re starting the next morning with a frozen load stuck to the floor and augers.
- Unload fully at the end of each feeding.
- Knock off buildup around the door and on the auger before it sets.
- If you can park inside or out of the wind, do it.
Tyres, hitch and lights
Short days mean more feeding in the dark. Check that lights work. Check tyre pressure, which drops as temperatures drop. And look at the hitch and safety chain. Frozen ruts and icy yards are hard on both.
Quick questions
Should I let the mixer warm up before loading? Running the auger empty for a short time at low speed lets the gearbox oil move before it takes a full load.
Can I mix frozen silage at all? Small frozen pieces are fine. Big frozen chunks should be broken up before they go in.
My scale reads different on cold mornings. Why? Cold can affect connections and power. Check connectors, cables and battery, then re-zero.
Is winter a good time for service? Yes. Book it early, before your dealer’s shop fills up.
Bottom line?
Winter doesn’t break good mixers. Skipped checks do. Spend an hour now on oil, knives, scales and clean-out, and your mornings go a lot smoother. If you want help with parts or a pre-winter look-over, talk to your LEO dealer. You can also see our VT twin auger feed mixers and heavy duty TMR mixers, built for year-round feeding.
Learn more about LEO Agriculture and our full line of feed mixers and manure spreaders.
